Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Chimney Company in Wells Branch, TX
Chimney repair in Wells Branch, TX most often comes down to age. The homes here were built mostly in the 1980s and 1990s, and many still have their original fireplace systems. We regularly work on chimneys that have not been looked at in 15 years or more, and the combination of North Austin weather and cheap, resinous local firewood means simple problems turn expensive when they are ignored. Boardwalk Chimney Sweep has served Wells Branch since 2011. Call (877) 274-1247 for a free estimate on any repair, sweep, or dryer vent job.
Why Wells Branch Homes Are Different
Wells Branch is a master-planned MUD community, and the housing stock follows a pattern: tract-built single-family homes and townhomes from the 1980s and 1990s, most with wood-burning fireplaces that were standard for Central Texas construction in that era. The fireplaces are either factory-built units or masonry boxes, and after 25 to 40 years, both types fail in predictable ways. Factory-built units develop rusted fireboxes and warped dampers. Masonry chimneys show cracked crowns and failed flashing around the roofline.
The bigger issue we see is creosote. Wells Branch sits at the edge of the Hill Country, and the cheapest firewood sold around here is ash juniper, what locals call cedar. It is everywhere in the greenbelt and it burns hot and fast, but it is full of resin. That resin turns into a sticky, glazed creosote that clings to flue walls instead of flaking off. Flues that look clean from the firebox often have Stage 3 glazed creosote higher up, and that is a chimney fire waiting on the right conditions. Winters here are mild but episodic. February 2021 showed what a hard freeze can do, and homeowners burn in bursts on those cold weekends, then let the fireplace sit idle for months. Creosote concentrates, moisture works in, and a dormant chimney is not a healthy chimney.
Styles & brands we work with
Our Main Wells Branch Services
Most Wells Branch homeowners call us for one of two things: a chimney that has not been swept in years, or a dryer vent that has never been cleaned. Here is how each works in this area.
Chimney Sweep in Wells Branch
Most chimneys in Wells Branch have either never been swept or were last done before the current owner bought the house. That is not an exaggeration; we regularly pull 15-plus years of buildup out of flues in subdivisions like Bratton Park and Wells Branch proper. What makes the job different here is the kind of buildup. The ash juniper sold cheap around the Hill Country produces creosote that gets dense and glossy, the kind that hardens onto flue walls and needs more than a standard brush pass. We handle it with rotary cleaning tools and a full inspection afterward. For details on this service, see Chimney Sweep in Wells Branch.
Dryer Vent Cleaning in Wells Branch
Dryer vents in Wells Branch are often long runs through walls or up through the roof in two-story homes, and lint collects at bends and terminations for years without anyone noticing. The National Fire Protection Association identifies dryer vent fires as a leading household fire cause, and we see the risk firsthand in this housing stock every week. We run a rotary brush and high-powered vacuum through the full vent run, clear the exterior termination, and check airflow. We bundle chimney sweeping with dryer vent cleaning under one call, addressing both combustion hazards in a single visit. See Dryer Vent Cleaning in Wells Branch for the full breakdown.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Chimney Repair in Wells Branch
Wells Branch chimneys are aging out of their original components. Factory-built fireplaces from the 1980s and 1990s were not designed to last 40 years without replacement parts, and masonry chimneys take constant weather at the roofline. The most common call we get is for a chimney that leaks, smokes back into the house, or has visible rust and spalling. The work usually involves the cap, the flashing, the crown, or the liner, and we repair what we inspect, meaning we do not recommend a fix without camera evidence you can see. For the full scope of what we handle, see Chimney Repair.
Chimney Cap Installation
Signs you need it
No cap at the top of the flue, or a cap so rusted that water and animals are getting in.
What it costs in Wells Branch
Chimney cap installation in Wells Branch typically runs $180 to $340 depending on flue size and whether the old cap needs removal.
How we do it
We measure the flue opening, select a stainless or copper cap from manufacturers like Olympia Chimney or Copperfield, and secure it to the crown with a mechanical fastener rather than sealant alone.
Chimney Flashing Repair
Signs you need it
Water stains on the ceiling near the chimney, damp insulation in the attic around the chimney chase, or visible gaps in the flashing where the chimney meets the roofline.
What it costs in Wells Branch
Chimney flashing repair in Wells Branch typically runs $300 to $600 depending on roof pitch, accessibility, and whether the existing flashing can be salvaged.
How we do it
We remove the old flashing or resecure it with proper layering into the shingles, using step flashing and counter-flashing that moves water away from the seam instead of trap it.
Chimney Crown Repair
Signs you need it
Cracks in the concrete crown at the top of a masonry chimney, chunks of crown falling away, or a crown with no overhang so water runs straight down the brick face.
What it costs in Wells Branch
Chimney crown repair in Wells Branch typically runs $250 to $550, with full crown rebuilds toward the higher end when the existing concrete is loose or missing.
How we do it
We clean out the damaged crown, build or seal a new concrete cap with a proper drip edge overhang, and apply waterproofing so the crown sheds water instead of absorbing it.
Chimney Liner Installation
Signs you need it
Gaps or cracks in the clay tile liner seen on a camera inspection, loose pieces of tile at the bottom of the flue, or a fireplace that drafts poorly even after a sweep.
What it costs in Wells Branch
Chimney liner installation in Wells Branch typically runs $900 to $2,500 for a single-flue fireplace, with cost varying by flue height, liner diameter, and whether the old liner needs demolition.
How we do it
We install a DuraFlex flexible liner system down the existing flue, insulation wrap it for draft and safety, and connect it to the appliance at the top and bottom with manufacturer-recognized components.
What Chimney Repair Costs in Wells Branch
| Item | Typical range in Wells Branch |
|---|---|
| Chimney cap installation | $180 – $340 |
| Chimney flashing repair | $300 – $600 |
| Chimney crown repair | $250 – $550 |
| Chimney liner installation | $900 – $2,500 |
Can a chimney with glazed creosote be repaired, or does it need a new liner?
Glazed creosote is a sweeping problem before it is a liner problem. We remove it first with a rotary cleaning, then inspect the liner with a camera. If the liner is sound, a HeatShield resurfacing can be applied to seal minor gaps and restore the flue surface without a full replacement. If the liner is cracked or missing sections, a DuraFlex liner install is the real fix.
Do I need a permit for chimney repair in Wells Branch?
Most cap, flashing, crown, and liner work in Wells Branch does not require a separate permit because it is a repair to an existing system rather than new construction. If your repair involves structural changes beyond the flue, your MUD or Travis County office may have a requirement, and we will tell you before work starts. Call (877) 274-1247 and we will walk you through what applies to your specific home.
Brands We Service in Wells Branch
We work with the brands chimney professionals specify: DuraFlex, HeatShield, Gelco, and Olympia Chimney. These are not off-the-shelf parts from a big-box shelf; they are the same materials used in commercial chimney work across the country. See our brands for the full list. Most Wells Branch jobs are completed with parts we carry on the truck, so there is no two-week wait on a cap or flashing order.
See the difference
Before
After
Before
After
Before
AfterPricing for Chimney Company in Wells Branch, TX
| Service | Typical range in Wells Branch |
|---|---|
| Standard chimney sweep (Level 1 inspection included) | $180 – $320 |
| Chimney sweep with heavy creosote removal (rotary cleaning) | $300 – $500 |
| Chimney cap installation | $180 – $340 |
| Chimney cap replacement | $220 – $400 |
| Chimney flashing repair | $300 – $600 |
| Chimney crown repair | $250 – $550 |
| Chimney liner installation (DuraFlex) | $900 – $2,500 |
| HeatShield resurfacing | $500 – $1,200 |
| Dryer vent cleaning | $120 – $250 |
The single biggest price driver in Wells Branch is creosote severity. A flue that has not been swept in a decade takes longer and needs rotary tools, so a sweep moves from the standard range into the heavy-removal range. The second driver is liner condition; the older the home, the more likely a sweep reveals cracks that need a liner fix. We give a flat price before work starts, and nothing gets added without a camera image showing you why.
Neighborhoods We Serve in Wells Branch
We work throughout the 78728 ZIP code and the surrounding streets, including the neighborhoods homeowners ask about most often.
- Wells Branch proper, including the original MUD subdivisions off Wells Port Drive
- Bratton Park and the townhome clusters along Bratton Lane
- The streets off Thermal Drive and around the Katherine Fleischer Park side
- Shoreline Drive and the sections bordering the Wells Branch greenbelt
We schedule jobs across Wells Branch weekly, and most repair estimates can happen within a few days of your call.
Service Area – Cities Near Wells Branch
We serve Wells Branch and the nearby North Austin communities. If you are in Windemere, TX, Pflugerville, TX, Anderson Mill, TX, or Jollyville, TX, we cover those areas as part of the same route. Scheduling works the same way: call, get an estimate, and we will put you on the calendar for the next available slot.
Serving Wells Branch, TX — Our Local Coverage Area
We’re based in the Wells Branch area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Chimney Company in Wells Branch
We schedule Wells Branch jobs weekly and can usually get a repair estimate on the calendar within a few days. Sweeps and dryer vent cleanings are faster to book. The seasonal rush starts in September and runs through January, so a call in early fall gets you in before the cold-weather backlog. Call (877) 274-1247 and we will give you the first available slot.
Wells Branch is a MUD community with active deed restrictions, and some neighborhoods require aesthetic approval for anything visible from the street, like a chimney cap color or crown coating. The restrictions apply to the look of the work, not the safety work itself. We can check what your specific section requires before installation so you are not dealing with a violation notice later.
Once a year, even if you burn only a few times. The episodic use pattern common in Wells Branch actually makes creosote worse, because each cold-weekend fire builds a fresh resin layer that hardens during the idle months. The National Fire Protection Association recommends annual inspection and sweeping as needed. A yearly visit catches glaze before it becomes a chimney fire.
If your Wells Branch chimney has not been inspected in years, or you need a straightforward sweep or dryer vent cleaning, call Boardwalk Chimney Sweep at (877) 274-1247 for a free estimate. We serve Wells Branch weekly and will tell you plainly what needs fixing now and what can wait.
What happens when you call
- 1A real person answersNo phone trees — talk to a local chimney cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you — the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Wells Branch Customers Say
"Thorough sweep and a clear report. He was running late from the job before and arrived near the end of the window, though he did call to warn me."
— Ruben Herrera"Creosote buildup was worse than I realized. He measured it, showed me the glazing on the flue with the camera, and was honest that we were closer to a chimney fire than I wanted to hear."
— Jennifer Vaughn"Cap keeps the birds out now, which after two springs of scratching noises is worth every penny."
— Sarah Bennett